纖維水泥泄爆墻安裝流程：

泄爆墻操作工藝流程：在已做好的地面或地枕帶上，放出隔墻位置線.窗門洞口邊框線，并放好頂龍骨位置邊線裝門洞口框:放線后按設計，先將隔墻的門洞口框安裝完成.裝沿頂龍骨和沿地龍骨:按已放好的隔墻位置線。線:依據設計工程圖按線安裝頂龍骨和地龍骨，用射釘固定于主體上，其射釘釘距為600mm。

在安裝頂地龍骨后，按泄壓板的規格1220mm板寬，分檔規格尺寸為612mm，不足模數的分檔應避開門洞框邊塊罩面板位置，使破邊罩面板不在靠洞框處.裝龍骨:按分檔位置安裝豎龍骨。龍骨分檔:依據隔墻放線門洞口位置豎龍骨上下兩端插入沿頂龍骨及沿地龍骨，調節垂直及定位**后，用抽芯鉚釘固定，靠墻.柱邊龍骨用射釘或木螺絲yu墻.柱固定，釘距為1000mm。

隔墻高度大于3m時應加橫向卡檔龍骨，采用抽芯鉚釘或螺栓固定裝罩面板：檢查龍骨安裝質量.門洞口框是不是相符設計及結構要求，龍骨距離是不是相符泄壓板寬度的模數。裝橫向卡檔龍骨:依據設計要求。
從屋門口處開始，無門洞口的墻體由墻的一端開始，泄壓板一般用自攻螺釘固定，板邊釘距為200mm，板中距離為300mm，螺釘距泄壓板邊緣的間距不得小于10mm，也不得大于16mm。安裝一側的泄壓板自攻螺釘固定時，泄壓板必須yu龍骨緊靠。

yu另一側泄壓板同時進行安裝填入安裝墻體另一側泄壓板:安裝手段同側泄壓板，其縫隙應yu側板面錯開安裝泄壓板:第二層板的固定手段yu層共同，但第三層板的縫隙yu層錯開。安裝墻體內電管.電盒和電箱設備安裝墻體內防火.隔音.防潮填充材料不能yu層的縫隙落在同一龍骨上。